Call

 

In this article in the next paragraph you might get more wonderful ideas in regards to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.

Installing a bathtub isn't specifically brain surgery, but it does require strong plumbing, woodworking, and in some cases, tiling abilities. Changing an old bath tub with a new one is likewise a moderately hard project. If the old bathtub is readily available, the job can relocate speedily; if you have to open a wall to eliminate the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either instance, the job is within a house handyman's abilities, although you will need a helper to move out the old bathtub and also embeded in the brand-new one. Make sure you have actually qualified on your own for the work as well as fit trying it. As opposed to hiring a service provider to take over a halfway-completed job, it is far better to take into consideration using one prior to you begin. Chances are you might need a specialist plumber to make tube links.
This write-up will certainly assist you set up a new bathtub in your bathroom if you have actually currently gotten a new bathtub and also don't require to alter the arrangement of your previous water supply pipelines.
Your tools and product checklist need to make up the following:

 

• New Bathtub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipe Caps


 

Planning for the Installation

First of all, the supporting framework provided with the bath should be fitted (if required) according to the maker's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to make sure that if the tap features a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the faucets device to avoid stress on the tub.
Fit the versatile tap connectors to the bottom of both faucets utilizing 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you utilize every one of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom ought to now prepare to be suited its last position.

 

 

Removing Old Taps

If you need to change old taps with new ones as a part of your installment, then the first thing you should do is disconnect the water system. After doing so, switch on the taps to drain any water remaining in the system. The procedure of getting rid of the existing faucets can be rather problematic due to the limited gain access to that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will originate from the pipes. When the supply pipes have been gotten rid of, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the single faucets from turning during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned of any kind of old sealing compound.
Before carrying on to fit the brand-new taps, contrast the pipeline links on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.

 

 

Setting up the Tub

Utilizing both wooden boards under its feet, put the bathtub in the required position. The wood boards are useful in evenly spreading out the weight of the bath tub over the area of the boards rather than focusing all the weight onto four little points.
The following goal is to make sure that the bathtub is leveled all round. This can be attained by checking the level and also adjusting the feet on the tub up until the level checks out level.
To set up taps, fit the bottom of the furthest flexible tap connector to the appropriate supply pipe by making a compression join; after that do the very same for the various other faucet.
Turn on the water system as well as inspect all joints and brand-new pipework for leakages as well as tighten them if needed. Fill up the bathtub as well as likewise inspect the overflow outlet as well as the normal outlet for leaks.
Ultimately, repair the bathroom paneling as defined in the maker's instruction manual. Tiling and also sealing around the bathtub needs to wait till the bathtub has been utilized at the very least once as this will certainly resolve it right into its final setting.

 

 

Fitting New Touches

If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to prevent damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the various other end gives a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will need decreasing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin making certain that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in position with the maker supplied backnut. When the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with typical tap connectors. The previous kind ought to be connected to the faucet ends first, tightening up only by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have been linked.

 

 

Tiling Around the Bathtub

In the area where the bathroom satisfies the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move sufficient to break a rigid seal, creating the water to permeate the wall surface between the bathroom as well as the tiling, leading to difficulties with moisture and also possible leakages to the ceiling below.
You can select from a selection of coloured sealants to assimilate your fixtures as well as installations. They are sold in tubes as well as cartridges, and also can sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with twists of soaked newspaper or soft rope. Remember to always fill the bathtub with water before sealing, to permit the activity experienced when the bathtub remains in usage. The sealer can split relatively early if you do not think about this movement before sealing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also easily available on the marketplace. It is suggested to fit the floor tiles utilizing water-resistant or water-proof sticky and cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Do you enjoy more info about Tools You Need to Install a New Bathtub ? Make a remark below. We will be delighted to see your suggestions about this content. We are looking forward that you visit us again in the future. Do you know another person who is sincerely interested in the niche? Feel free to promote it. I truly appreciate reading our article about How to Install a Bathtub.

Stress less, ring us.